Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Can I Set Up a Tub Myself? Factors to Consider As Well As Steps
Blog Article
Just how do you really feel in regards to How to Install a Bathtub?
Mounting a bathtub isn't exactly rocket science, but it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you need to open a wall to remove the old bathtub and also place the new bathtub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to leave the old tub and also embeded in the brand-new one. Ensure you have certified on your own for the task and fit trying it. As opposed to working with a service provider to take over a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new tub in your shower room if you have actually currently acquired a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your devices and product list must comprise the following:
Getting ready for the Installment
To start with, the sustaining structure supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Making use of the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are practical in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reads degree.
To set up faucets, fit the bottom of the furthest flexible faucet port to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Turn on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub should wait until the tub has actually been made use of at least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washers remain in area between the tap and also the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are marketed in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to permit the movement experienced when the bathtub remains in use. The sealant can crack fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily available on the market. It is a good idea to fit the tiles utilizing water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about Installing A Bathtub? Try leaving feedback directly below. We would be pleased to know your ideas about this piece. Hoping to see you back again in the near future. Enjoyed our blog posting? Please share it. Help another person check it out. We truly appreciate reading our article about How to Install a Bathtub Yourself.
Prices & Booking
Report this page